Article

Section 1 cutting out general operating standards
One, find the right paperVersion, to cut the clothing style number and version to be on;
Two, row wheat rack:
01, according to the production order of the cutting machine, measure the actual width of the cloth, minus half an inch on each side, if there is a dead mark on the edge of the cloth should be set separately;
02, when typesetting, should be combined with the actual poor performance of the cloth, to determine whether the reverse row seam together, cut pieces as close as possible to its seam, to avoid color difference;
03. Refer to the data to check whether there are omissions in the cut pieces;
Three, Raab:
01. Clarify the type, color and amount of cloth used according to the production order;
02, take one end of a right Angle into 90 degrees as the basis, when the stripes should be straightened, cloth edge consistent, cloth edge should be straightened and flat, for some slight inclined cloth is pulled by hand. In principle, the evening dress is more than 3 inches, the white yarn is more than 2 inches, the weft inclined cloth cannot be cut, the Labab tightness should be moderate, and it is natural and smooth;
03. After drawing, check the color and layer number of the cloth in the production single;
Four, cutting:
01. According to the production single, the type, color, number and number of the cloth of the wheat rack are comprehensively rechecked;
02, when cutting must be cut in the line, not online inside and outside the cut, straight line to straight, arc to round, mark clear;
03, complete the cut piece and the paper version is completely consistent with the color difference of the cloth, should leave the triangular position, write the number;
04, the original cloth defects should be repaired;
05. The roll number, cylinder number, quantity, secondary cloth and loss of the cloth to be cut shall be indicated on the production sheet of cutting bed.
V. Film examination:
01, according to the production order, check the cut piece number, size, color difference, color matching cloth type, cut piece small parts, fabric grain warp, quantity, etc.;
02. The number and name of the cut pieces to be changed shall be indicated in the production and matching record book to prevent the color difference or mistake and omission from being checked;
VI. Subcontracting:
01, according to the production order, each number is separately bandaged. The package with the same serial number shall be marked with the item number, number, number of pieces and serial number of the sticker;
02, pay attention to not fold the cloth, the application of lining and paper lining to do the core, cylindrical, to prevent creases, special single other wrapping;
Seven, clean the table:
Clean up the cut table, and then do the next one;
Eight, the paper version:
Put away the sheets in order and put them back in the correct position.
IX. Receipt and dispatch:
01. Check the cut pieces according to the style number, color and quantity of the production order of the cutting bed. Refer to the shipping list of the week, send out the urgent parts, machine embroidery, nail bead and flower arrangement in order first;
02. Each type of cut piece to be shipped next week must be sent out one week in advance;
_____________________________________________________________________
The second section ironing lining
First, understand the structure of the cut piece, ironing lining ironing temperature should be appropriate, put the cloth flat first, if there is a cloth wrinkle need to be ironed first;
Second, according to the performance of the actual cloth, distinguish the positive and negative of the cloth, and put the grain straight;
Three, the lining is flat, not out of position with the cut piece, must be consistent, ironing lining should be ironed firmly, can not loose foam;
_____________________________________________________________________
The third section of the pruning point

One, trim:
First of all, we should distinguish the number of money, the number of yards, find out the corresponding paper, put the cutting grain, fixed, trim to be accurate, tooth scissors to be obvious;
2. Point location:
Distinguish the money number, separate the code number, find out the corresponding paper, paper and cut piece completely consistent, point position to be accurate and clear;
_____________________________________________________________________
Section 4 Standards for Making Needle Car
01, Princess Sew:
BP point should not be high or low, BP point, waist joint alignment should be accurate, the turning line should be round, the upper and lower cut pieces should be consistent in tightness, the needle distance (according to) should not be lower than every inch: 11 stitches for white piece, 9 stitches for waist connection, 9 stitches for evening wear except for sleeve long rolling strip, and 11 stitches for others;
02. Conjoint coedge:
Pay attention to the seams and measure the chest and waist circumference (according to the size table, not less than the size table, nor more than 1/2 inch);
03, Medium Perm (1) :
There can be no dead seam, seam need to open flat, there can be no wrinkle phenomenon;
04, Medium Perm (IV) :
Collar to shrink seam, can not be pulled loose, hot to be able to match the original; The lower end of the fold can not dimple, to smooth;
05. Upper zipper:
The tightness between lining cloth, face cloth and zipper should be consistent, and can not show wavy shape. In case of bone, water-soluble lace, tooth, etc., 1/16 inch should be set aside to prevent the head from getting stuck. The tail of the chain should not dimple or wrinkle. The tightness should be consistent and the appearance should be like a natural plain coat.
06. Sleeve Up:
The sleeve hill should be round and full, the sleeve seam must not be slanted, and the sleeve position should be correct.
07, Medium (3) :
The sleeve can not be ironed dead, first from the inside of the ironing seam (ironing sleeve);
08, top collar, collar paste:
To shrink seam appropriate, can not fold, can not pull loose, check whether there is deformation with the pattern, pay attention to the size;
09, joint collar, collar paste:
The seam can not be skewed, so as not to lead to deformation of the collar paste;
10. Reasonable distribution:
The surface and lining waist should be sewn and leveled without tension or excessive capacity. The lining seam at the end of the zipper should be centered.
11. Pedicure:
To distinguish the money number, wear the correct platform, the size should be accurate, pay attention to the special size sheet, the whole circle of the skirt foot should be smooth, and the wavy shape is forbidden;
12, medium (4) :
For ironing skirt hem, first flatten the edge line, and then smooth it according to the size of the hem folding;
13. Sleeve joint:
According to the seam mark car, subsidy avoid elongated;
14. Skirt pleats:
Note that the fold of the skirt is thin and dense, the size is uniform, and the left and right sides are symmetrical. The pleats are drawn according to the mark of the mouth. The pleats must be straight and not too open according to the cutting size.
15. Making lining:
According to the seam share mark, the needle distance per inch should not be less than 10 stitches, the thread should be smooth, pay attention to the tightness of the thread, do not float the thread jump needle and other phenomena, pay attention to the height of teeth, do not bite the lining;
16. Lining hem and fork:
The width and width of the lining edge should be consistent. When closing the fork, the bottom lining cloth should be released more than 3/8 inches on the basis of the surface cloth to prevent the bottom fork from turning out. The length of the fork should conform to the size according to different styles (see the size table). The length of both sides and the tightness in the surface of the fork should be the same, without wrinkle or inequality;
17. Hemming of lower skirt:
Pay attention to the different kinds of cloth, the tightness should be appropriate, pay attention to the hip circumference, waist size, the sling car under the clamp ring 1/2 inch (finished product);
18, medium (5) :
Ironing skirt seams, can not have dead marks, seams should be flat;
19. Sealing pin:
First distinguish the style number is made with pure silk or chemical fiber standard, pay attention to all kinds of marks, the number of yards;
Book mark:
Make clear the size of the collar and then nail the label, the sealing is smooth, the needle surface should be sewn, the finished product appearance should be plain clothes;
20. Connecting waist and neckline:
(01) The LACE at the collar should be straight, without distortion or skew; (01) The LACE at the neck should be straight, and the LACE at the neck should be straight, without distortion or skew.
(02) Flat waist line should be round, sharp waist herringbone should be pointed, to take stick, there is a bud waist, pay attention to the size of the bud, bud cloth and cloth cloth to be consistent;
21. Make shoulder cotton and wrap rolling strip:
The rolling bar should not be too tight or too loose. The size of the rolling bar should be uniform, full, not empty, round, and not concave-convex.
22. Car hem:
The seam share should be uniform, and there can be no irregular size, burr, double fold and other phenomena;
23. Ironing hem:
The thread should be smooth, and every seam should be ironed flat. No marks;
24. Beat the edge:
Pay attention to the straight seam, the thinness and tightness of the line, cut the line, the twill parts should not be pulled loose, and the edge should be consistent with the original one.
25. Paid Skirt:
Rough net drawing fold, rolling symmetrical and uniform, fixed coarse net, symmetrical, uniform, according to the cutting bed point mark fixed, under the bottom foot rolling edge to smooth, can not have wide, narrow, twist and other phenomena;
26. Flower arrangement:
Pay attention to the appropriate tightness of the LACE stitched on the princess. Where flowers are added, both sides should be symmetrical. Pay attention to the color difference of LACE and the main cloth, and LACE is symmetrical and attached to the cloth.
27, car flowers: reinspection row flowers;
Flowers can not shift, pay attention to cloth, needle size, moderate line. Can not bubble, so as to avoid the bottom line of the skin or face cloth wrinkle, must be along the edge of the triangle needle lace car, car line can not run on the main flower! So as not to affect the appearance of the flower!
28. Bead sewing:
Sew beads according to the sample or bead version to do, pay attention to the tightness of the needle and thread. Nailbead shaped lines, the same aesthetic degree or more perfect than sample clothing (small sample);
_____________________________________________________________________
Section 5: Operation standards for quality inspection
01, the quality inspection table clean, put their own quality inspection equipment on their most convenient position;
02, after taking off the clothes, carefully look at the flying son, the flying son and clothing style number, color, size of the check;
03. Look carefully at the key size sheet for the sample production of this style;
04, put the clothes on the right platform, pull the whole line of the clothes;
05, according to the size table, measure each detail size (body length, chest, waist, collar, clip, waist splicing, etc.) :
(1) the length of the body: Jin fosso line 1/4 inch set, connected with the size table size to the foot (front foot center);
(2) chest circumference: according to the size table from the armpit 1/2 inch through the BP point measure a circle;
(3) Waist circumference: according to the size table, measure one circle through each point of the waist (note that individual style should measure the inner waist ring);
(4) Neckline: measure the size of front collar and back collar along the collar edge according to the size table. The details should be consistent with the sample, and the design line of the whole garment is deformed and out of shape with the sample;
06, quality inspection of the whole piece is drawn, roving, dirty, color difference, defects, etc., pay attention to the cloth line;
07, check whether the upper body deformation (collar, sleeve, chest size, etc.), if in doubt, according to the paper version check whether the repair piece is consistent;
08, check whether the folding position is symmetrical, the middle point of the waist sewing is smooth;
09, check the line tightness, thin density must be moderate;
10, according to the sample clothing compare quality inspection arrangement of flowers have no deformation, no wrong row leakage, symmetrical (allowable error is not visible to the naked eye);
11. Whether there is color difference, deformation and positioning of LACE LACE, whether the thread leaks out of the flowers, whether the flowers are deformed, check the BP point to see if there is shrinkage;
12, quality inspection upper collar, cuff ring is not exposed, whether the seam is ironed, whether the cloth is ironed, dead marks, line marks;
13, quality inspection of the whole waist, car zipper process, finished line on the original design has no influence, etc. Check whether the feet are trimmed according to the correct size, check whether it is a special size list;
_____________________________________________________________________
Section 6 Handmade Standards
01. Wire repair:
All threads should be absolutely clean;
02, button door position:
According to the paper point accuracy;
03, button door position:
The position should be correct, check the line;
04, the buttoning position to be accurate, the buttoning position to be correct, to nail firmly, parallel lines neat, the buttoning thread, stitching to hide;
05, nail shoulder cotton:
Pay attention to the position, smooth appearance, no wrinkle or inequality. Do not nail to the cloth or elsewhere;
06, manual nail needle can not be twisted, stitching thread to hide;
07, collar skirt nail hook:
Note that both sides should be the same height, to nail, buttoning up to make the appearance of the table level, to serve the table;
08, pull lugs:
According to the distance in the table, the appearance of the finished product is straight and smooth, and the line ear must not be too long or too short;
09. Stitching Caterpillar:
Caterpillar 1/4 inch long, the position should be appropriate, the knot should be firm, so as not to fall off scattered;
10. Picking the foot:
Pay attention to the line thin density should be balanced, needle distance is not less than 1/4 "; Needles should be properly tightness, stitches should not leak out, the whole circle should be smooth, not twisted;
11. Making Handcrafts:
Pay attention to the whole dress handmade flowers should conform to the original practice, the size of the sewing position, iris: uniform size, symmetrical can not skew;
12. Replenishing beads:
Pay attention to the tightness of the needle, the shape of the nail bead, the smoothness and softness of the branch and rod. The LACE part is a necessary part of the dividing line. The beads are clearly separated and should not be confused. According to the sample or paper version, the aesthetic degree should be the same or more than the sample;
13, package button:
Can not hair feet, pay attention to the color difference;
_____________________________________________________________________
Section 7: Hot
Big hot, again to remedy defects in the process of lathe, hot out the finished appearance lines, after the hot must not have dead marks, line marks and other defects. When ironing, we should grasp the principle of neckline shrinkage, chest and waist alignment, not stretching, and pay attention to the integrity and beauty of the whole garment.
_____________________________________________________________________
Section 8: Finishing and washing oil

A, check whether there are dead hot marks, there are returned;
Two, check whether there are mistakes or omissions;
Three, check the appearance of the whole piece of clothing, leader and other symmetry;
Four, the washing oil must be absolutely clean, after the completion of the clothes all dirt and thread must be absolutely spotless;
5. Make a comprehensive inspection of the above procedures and arrange the whole garment, such as mending beads, mending flowers, mending embroidery and stitching, etc.
6. Check whether there is any difference in the same degree, style number and color match between the finished clothes and the original sample;
_____________________________________________________________________
Section 9: Packing of hanging tags
First, check the washing oil 100% to check whether there are clothes defects, check whether the color of the fly is the same with the order, style number and size number, carefully write the packing list, pay attention to the special size list, accessories and different styles of the same SO# color is the same, and make no mistakes.